HOWTO

TPP: Patton Trinity SmartNode (kb4824)

Le informazioni contenute nel presente articolo riguardano i seguenti prodotti:

  • SwyxWare 2015
  • Patton Trinity SmartNode (3.9.3 (June 2016))

[ Riepilogo | Informazioni | Referenze ]


Riepilogo

Within the Swyx Technology Partner Programme (TPP) the  Patton Trinity SmartNode was successfully tested and hereby reaches the certification level certified.

This KB article describes all mandatory configuration steps that need to be performed to assure a flawless operation between a Patton Trinity SmartNode and a SwyxWare2015.


Informazioni

1. Certification test

The tests were executed between both a Patton Trinity SmartNode 4130 (BRI) and Trinity SmartNode 4170 (PRI)  and two SwyxWare installations in Master-Standby operation.

Versions

The following combinations were tested:

  • SwyxWare2015 R3, with Patton Trinity SmartNode4130, Firmware Trinity 3.9.3 (June 2016); test date: 10.06.2016
  • SwyxWare2015 R3, with Patton Trinity SmartNode4170Firmware Trinity 3.9.3 (June 2016); test date: 16.06.2016

Endpoints:

SwyxIt!
SwyxIt! (via RemoteConnector at SwyxWare2015)
SwyxPhone      L615
SwyxSIPPhone S315
SwyxPhone D510 via DECT500

1.1 Executed tests

Inbound and outbound calls with the above endpoints from and to PSTN / GSM

  • Signaling
  • CLIP
  • CLIR
  • CLIP No Screening
  • Long duration calls
  • Hold / Retrieve
  • Call toggeling
  • Transfer
  • Conferencing
  • Call forwarding internal/external
  • DTMF Signaling
  • T.38 negotiation and FAX transmission
  • CTI+

All testcases were completed sucessfully.

Restrictions
If a call through CTI+ is not accepted by the called party, a timeout occurs in both the Patton GW and the SwyxWare. This leads to the situation that the auxiliary call is not terminated automatically, but has to be terminated manually by the user on the controlled device. 

2. Start-up

The following steps are necessary for a start-up:

  • Creation of a SIP gateway trunk und SwyxWare user; configuration of SwyxWare locations if necessary
  • Preparation of the Patton Trinity SmartNode
  • Adjustment and installation of the Patton Trinity SmartNode configuration file

2.1. Preparation of SwyxWare

  1. Using the configuration assistant, create a new SIP Gateway Trunk group within the SwyxWare. Select the Trunk Group Profile "SwyxConnect" that fits to your PSTN connection.
  2. Create a new SIP Gateway Trunk for the newly created SIP Gateway Trunk Group.
  3. Configure "SIP-User-ID" and "SIP Username" with a value of your choice, use the same value for both items.
  4. Configure the SIP password.
  5. Configure the available range of external numbers.
  6. Activate all codecs.
  7. Configure the number of available channels.
  8. Set the local NetBIOS name as "Computername".

Afterwards, open the properties of the newly created SIP Gateway Trunk.

  1. In the tab "Encryption", set the encryption mode to "No Encryption".

2.2. Preparation of Patton Trinity SmartNode

Update the firmware of the Patton Trinity SmartNode to the tested version Firmware Trinity 3.9.3 (June 2016) before adjusting the configuration. The appropriate firmware can be found at  http://www.patton.com/support/upgrades/index.asp?t=SmartNode. You need an account and password from Patton to download the firmware.

Connect the Trinity SmartNode through the network interface ETH 0/0 with your LAN. The Trinity SmartNode is configured as DHCP Client. Please check the lease table of your DHCP server to detect the assigned IP address.

Log in through the web interface of the Trinity SmartNode:

Username: administrator
No password

Left in the menu (three horizontal lines) select "System -> Firmware upgrade"
Use the field "Browse" to select and upgrade the firmware.
The filename contains the model of the Trinity Smartnaode and the firmware version, i.e. SN4130_3.9.3.tar.
Afterwards, the Trinity SmartNode is restarted and uses the new firmware.

2.3. Configuration and Installation of the INI Files

At the end of this article, you can download a zip-file with several configuration templates. Download the one that fits to your PSTN-Connection.

2.3.1 Configuration of the INI file

Open the chosen configuration template with a text editor, find the following terms and replace them with the appropriate settings. Note: A term may occur several times in the configuration template and must be replaced accordingly.

STANDALONE:

  • IP-PBXSERVER    IP Address of your SwyxWare server
  • SIP-NAME        SIP-User-ID / Username of your trunk
  • SIP-PASSWORD    Password of your trunk
  • SIP-REALM       Standard realm for SIP clients

MASTER-STANDBY

  • IP-PBXSERVER-MASTER      IP Address of your Master SwyxWare server
  • IP-PBXSERVER-STANDBY     IP Address of your Standby SwyxWare server
  • SIP-NAME                 SIP-User-ID / Username of your trunk
  • SIP-PASSWORD             Password of your trunk
  • SIP-REALM                Standard realm for SIP clients

Save the changes after adjusting the configuration file.

2.3.2 Installation of the INI file

After the reboot, logon with the Trinity SmartNode once again and upload the adopted configuiration file:
In the left menu (three horizontal lines), select "System -> Configuration files".
On the left side of the dialog, first select "startup-config", then select the item "Upload".
In the following dialog, click "Browse" to upload the configuration file.
Afterwards, close all open configuration dialogs. On the left menu (three horizontal lines), select "Reboot".

The Trinity SmartNode will restart with the new configuration file and will register on the SwyxWare.


Referenze

As far as software supplied or used by us, includes open source elements the additional terms under https://www.swyx.com/open-source apply in addition. An overview which products from the Swyx portfolio include open source elements and which open source license is relevant can be found under https://www.swyx.com/open-source.

Informazioni di altri produttori proposte in questo articolo hanno il compito di appoggiare la ricerca di informazioni tecniche. I contenuti potrebbero essere modificati senza preavviso. Swyx non garantisce per la veridicità dei contenuti di articoli di terzi e declina ogni responsabilità per essi.


Commento

L'articolo è stato utile? Lasci un commento all'articolo



Come possiamo contattarLa se dal Suo commento dovessero nascere altri quesiti?

Indirizzo e-mail Adresse (facoltativo)


Nota

Il campo destinato ai commenti non è ammesso per richieste all'assistenza. Per quesiti inerenti l'assistenza rivolgersi esclusivamente al proprio rivenditore di fiducia o al distributore competente.