INFO

SIP Provider OpenIP (FR) (kb4571)

Le informazioni contenute nel presente articolo riguardano i seguenti prodotti:

  • SwyxWare 11
  • SwyxWare 2015

[ Riepilogo | Informazioni | Referenze ]


Riepilogo

Information und configuration hints for SIP provider OpenIP (France).


Informazioni

General information

The following information are valid for a SwyxWare 11 or later and cannot necessarily applied to earlier versions.
OpenIP  is offering a SIP trunk with user authentication. Along with the assigned number range and server information, you also need UserID, UserName and UserPassword. Please be aware that the naming may differ, or you might have only received UserName and -password. In this case, UserID and UserName are identical.

There is a dedicated SwyxWare profile for the OpenIP SIP trunks available. OpenIP therefore must be informed if a SwyxWare is connected to their SIP trunk. Otherwise there is a risk of problems in the SIP communication and number format.

Configuration

In order to assign incoming calls to the correct trunk, it is necessary to configure a SIP URI for the trunk. The assigned number block and the numberformat must be considered.

Example
Numberblock: +33 970 112230 ... +33 970112239
In this case the SIP URI must be entered in the format +3397011223*@* .

For your convenience the generated CustomProviderProfiles.config is available for download at the end of this article. Extended information about how to use this file can be found at Configuration and Adaptation of SIP Providers via Provider Profiles (kb3436).

Important: From SwyxWare 11.10.0.0 on, the provider profile for OpenIP is already available in the list of provider profiles and the CustomProviderProfiles.config is no longer necessary.
 

Tested Features

  • Incoming/outgoing national calls
  • Incoming/outgoing international calls
  • Correct Calling Line Identificaion (CLI) on national and international calls
  • Holding and retrieving calls
  • Toggeling between two calls
  • Call transfer
  • Conferencing
  • Mutually supported audio codec:
    • G.711u
  • Incoming/outgoing DTMF signaling in accordance with via RFC2833
  • FAX transmission via G.711

FAX transmission

OpenIP does not support the T.38 protocol, which is strongly recommended for FAX transmission in an IP environment. The alternative method for FAX transmission via G.711 is supported from SwyxWare2015R3 on. In oder to prevent the intended T.38 stream switch, it is necessary to remove the T.38 codec from the list of supported codecs.
Note: Quality and reliability of a FAX transmission via G.711 strongly depends on the end-to-end network connection. Since the control and redundancy information from the T.38 protocol are missing, especially the transmission of larger documents may fail.

Limitations
  • none

Test date:
15/01/2014 with SwyxWare2013 R3
30/06/2015 with SwyxWare2015 R2
27/11/2017 with SwyxWare 11

Overview of tested SIP provider


Referenze

As far as software supplied or used by us, includes open source elements the additional terms under https://www.swyx.com/open-source apply in addition. An overview which products from the Swyx portfolio include open source elements and which open source license is relevant can be found under https://www.swyx.com/open-source.

Informazioni di altri produttori proposte in questo articolo hanno il compito di appoggiare la ricerca di informazioni tecniche. I contenuti potrebbero essere modificati senza preavviso. Swyx non garantisce per la veridicità dei contenuti di articoli di terzi e declina ogni responsabilità per essi.


Commento

L'articolo è stato utile? Lasci un commento all'articolo



Come possiamo contattarLa se dal Suo commento dovessero nascere altri quesiti?

Indirizzo e-mail Adresse (facoltativo)


Nota

Il campo destinato ai commenti non è ammesso per richieste all'assistenza. Per quesiti inerenti l'assistenza rivolgersi esclusivamente al proprio rivenditore di fiducia o al distributore competente.