HOWTO

Initial configuration of tiptel innovaphone 21 (IP21) for interoperability with SwyxWare (kb2315)

Le informazioni contenute nel presente articolo riguardano i seguenti prodotti:

  • SwyxWare v4.13
  • SwyxWare v4.12
  • SwyxWare v4.11
  • Innovaphone IP21 4.x
  • SwyxWare v4.02

[ Riepilogo | Informazioni | Referenze ]


Riepilogo

This article describes the initial configuration of IP21 by Webinterface (enter IP address of device) after reset/using factory defaults.

The latest firmware version being tested with SwyxWare is

  • v4.00 sr2 [02-4283] (see download reference below)

Informazioni

To start configuration window:

  • Click Gateway Config
      (or 'Administration: Config edit' until firmware 4.00 rc1)
  • Login using default user/password (admin/ip21)
  • Choose Config/IP Interfaces/Ethernet Interface
  • Set DHCP Mode to Client

Configuring analog line 1 (using GW1/TEL1):

  • Choose Config/VoIP Interfaces/Undefined GW1
  • Set Mode to Registration at gatekeeper as endpoint
  • Set Remote gatekeeper address/IP address to IP address of IpPbxServer
  • Choose Config/VoIP Interfaces/GW1
  • Click button Add alias
  • Enter H.323 alias of terminal adapter user (as configured in SwyxWare Administration) in H.323 Name

  • Choose Config/Routing table
  • Click button Add route
  • Choose Config/Routing table/Route/->TEL1
  • Set Enable calls from interfaces to GW1 => Route GW1->TEL1
  • Click button Add map
  • Fields could be left empty
  • Set Destination: to TEL1

  • Choose Config/Routing table
  • Click button Add route
  • Choose Config/Routing table/Route/->TEL1
  • Set Enable calls from interfaces to TEL1
  • Set Default call destination to GW1 => Route TEL1->GW1
  • Click button Add map
  • Fields could be left empty
  • Set Destination: to GW1

To configure IP21 for T.38 (Fax over IP) protocol (SwyxWare >= v4.02)

  • Choose Config/VoIP Interfaces/GW1
  • Set Enable T.38 fax protocol flag

    T.38 configuration
    T.38 configuration
    Cliccare per ingrandire...

Click buttons Activate and Save to activate and save the new settings.

To configure analog line 2 the same procedure should be done using GW2/TEL2 instead of GW1/TEL1.

 

Note:

Do not configure the IP21 and the SwyxWare to TCP but instead use the default UDP. The SwyxWare is currently not compatible to the IP21-TCP. The Knowledgebase article Usage of Fax T.38 via TCP instead of UDP (kb2291) is meant for stand-alone SwyxGates being used for internal S0/S2m lines to connect FAX devices to.


Referenze

As far as software supplied or used by us, includes open source elements the additional terms under https://www.swyx.com/open-source apply in addition. An overview which products from the Swyx portfolio include open source elements and which open source license is relevant can be found under https://www.swyx.com/open-source.

Informazioni di altri produttori proposte in questo articolo hanno il compito di appoggiare la ricerca di informazioni tecniche. I contenuti potrebbero essere modificati senza preavviso. Swyx non garantisce per la veridicità dei contenuti di articoli di terzi e declina ogni responsabilità per essi.


Commento

L'articolo è stato utile? Lasci un commento all'articolo



Come possiamo contattarLa se dal Suo commento dovessero nascere altri quesiti?

Indirizzo e-mail Adresse (facoltativo)


Nota

Il campo destinato ai commenti non è ammesso per richieste all'assistenza. Per quesiti inerenti l'assistenza rivolgersi esclusivamente al proprio rivenditore di fiducia o al distributore competente.